Alphacool Eisstation 80 DC-LT - reservoir

The Eisstation DC-LT Solo Top from the Enterprise Solutions series is an extremely compact pump top and is very powerful together with the DC-LT pump. It shows its strengths wherever space is at a premium or where a pump needs to be accommodated in a space-saving manner. The Top is compatible with the DC-LT pump series and is also well suited for small water cooling systems including 1U server racks. If the upper aluminium plate (don’t worry, this doesn’t touch fluid) is removed, the top can also be extended with a reservoir. Under the plate there is also a bubble down filter which minimizes the suction of air bubbles. With the reservoir combination, the pump top corresponds to the Eisstation 40 DC-LT series. You can put the pump top almost anywhere; it is very practical and versatile. The included accessories a Velcro mat with which the top can be fixed anywhere in the housing. There is a Velcro mat included with the accessories which adheres very well and provides a secure hold. If you prefer to use mounting feet, you can order them separately and install the Eisstation at multiple angles such as 30 degrees or 90 degrees. To install the pump, remove the plate on the bottom and insert the O-ring. The pump is then screwed down and the plate reattached. This way the pump is completely covered by the top and protected from all sides.

The Eisstation 40 DC-LT of the Enterprise Solutions series corresponds to the above Solo Top and is therefore also extremely compact. This however comes with a reservoir. It also fits into 1U server racks but can also be mounted directly on a radiator. Together the Solo Top and reservoir are only 6 cm long, 4 cm wide and 4.1 cm high. That's why it also fits on a 40 mm Alphacool X-Flow NexXxoS radiator. Despite its size, just under 30 ml of coolant still fits inside and since it can be connected directly to a radiator, it too acts as a reservoir. As with the Solo Top, the filter prevents air bubbles from entering the pump. The included double nipple allows the Eisstation to be connected directly to one of the four G1/4" threads at the side or front entrance of the radiator. The Eisstation, together with a NexXxoS 40 mm X-Flow radiator fits easily into a 1U server housing. 

The Eisstation 80 DC-LT of the Enterprise Solutions series, on the other hand, still fits into 2U server racks, depending on the installation method. The entire Eisstation is made of acetal and is therefore extremely resistant and durable. As with the Solo Top, a Velcro mat is included with which the Eisstation can be mounted without losing its compact design. In contrast to the other Eisstation, mounting feet are included to adjust the height. Mounting at an angle of 30 degrees or 90 degrees is also possible. The volume can be reduced by using the enclosed decoupling feet. The installation of the pump is the same as with the other two items. Only the filling is easier, because through the 25mm large filling opening, spray bottles or funnels can be used easily. When the pump top is used together with the reservoir, the inlet is on the side of the reservoir and the outlet on the side of the pump top. If IN and OUT are to run in a certain direction, the reservoir can also be dismantled and turned into any position. If the reservoir is not used, there is an additional input on the opposite side of the OUT.

Eisstation 80 DC-LT

Scope of delivery:

• 1x Reservoir
• 1x Screw plug G1/4"
• 1x Screw plug G1"
• 2x M3x8 screws
• 8x M4x6 screws
• 2x M3x5 screws
• 1x Screw plugs - Tool
• 1x Hexagon key
• 1x Velcro mat
• 2x Feet
• 4x M4 nuts
• 4x vibration damper

Technical Data:

• Dimensions: 50.62 x 50.62 x 77 mm (W x D x H)
• Net weight: 144 g
• Maximum working temperature: 60 °C
• Connections: 3x G1/4"
• Pressure tested: 1,5 Bar
• Certificates: CE, FC, ROHS

Information & Assembly instructions EN (See page 3 for manual.)